Crucial CP16G60C36U5B 16GB DDR5 6000 desktop RAM
- 16 GB
- DDR5 6000
We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.
A 4 GB DDR3 DIMM running at 1600 MHz with CL11 latency and 1.5 V for HP desktops using part numbers 655410-D88, 717046-001 or 688600-001
This 4GB DDR3 module is a direct replacement for HP part numbers 655410-D88, 717046-001 and 688600-001. It operates at 1600MHz with a CL11 latency and standard 1.5V voltage. The unbuffered, non-ECC DIMM uses a 240-pin interface and a 2Rx8 chip organisation. It is built for desktop systems that require these exact HP specifications.
This module suits owners of compatible HP desktops needing a 4GB DDR3 upgrade to match the original factory specification. Systems that require ECC memory, registered DIMMs, a different voltage, or a higher density per slot should look at alternative modules. Compatibility depends on the motherboard accepting 2Rx8 unbuffered DDR3 at 1.5V.
The 2Rx8 chip organisation is the critical specification that determines whether this module will work in a given HP desktop. Some HP platforms only accept 1Rx8 or 1Rx16 configurations and will not post with a 2Rx8 stick. Verify the original module label or the system service manual for the rank and organisation details before purchasing.
Measured against everything we stock in Desktop RAM, at today’s prices. Recalculated every night.
New to this? Buying memory and SSDs with crypto — what to check, what it costs to pay, and what is never asked for.
| Product | |
|---|---|
| Brand name | A-Tech |
| Product line | Compatible Replacement for HP |
| Model name | 655410-D88, 717046-001, 688600-001 |
| Total capacity | 4 GB |
| Performance | |
| Rated speed | DDR3 1600 (PC3 12800) |
| Processor | |
| Chipset | Major Brand Chipset |
| Memory | |
| CAS latency | CL11 |
| Tested speed | 1600 |
| ECC support | No |
| Buffer type | Unbuffered |
| Heat spreader | No |
| Power | |
| Rated voltage | 1.5 V |
| Compatibility | |
| Recommended for | Compatible Replacement for HP 655410-D88, 717046-001, 688600-001 |
The module runs at 1600 MHz with a peak transfer rate of 12800 MB/s; actual bandwidth depends on the motherboard's memory controller and whether it operates in single- or dual-channel mode.
The stick uses the standard 240-pin DDR3 DIMM form factor, so it fits any desktop board that accepts unbuffered non-ECC DDR3 DIMMs; verify your model's maximum capacity per slot before installing.
Power off the PC, open the case, align the notch on the 240-pin edge connector with the slot key, press firmly until both retention clips click, then power on; the frequent error is stopping before the clips latch, leaving the module partially seated.
More in Desktop RAM
What you pay in, and what you read prices in.
Sent from your wallet at checkout
Display only — the catalogue is priced in USD
No currency matches that.
New here?
Already have one?
There is no automatic reset: this shop sends no mail, so there is no one-time link to ask for. Leave the address on the account and it gets picked up by hand.
Request noted
Nothing is on its way to your inbox — this shop sends no mail at all. Someone picks these up by hand.
Remembered it?