Crucial CT2K8G3S160BM 16GB (2 x 8GB) DDR3 1600 SO-DIMM memory upgrade
- 16 GB (2 × 8 GB)
- DDR3 1600
We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.
16 GB DDR3L 1600 kit with two 8 GB SODIMMs for compatible HP Envy TouchSmart notebooks
This 16 GB kit contains two 8 GB DDR3L SO-DIMM modules built for the HP Envy TouchSmart m7-j120dx, m7-j178ca and m7-1015dx. The unbuffered, non-ECC memory runs at 1.35 V and matches the factory slot layout of two sockets. Buyers needing more than 16 GB or a different form factor cannot use this upgrade.
Operating at the low 1.35 V DDR3L level, the modules draw minimal power and produce little heat during everyday tasks. No heat spreader is fitted, so airflow in the notebook chassis handles cooling silently. The CL11 11-11-11 timing keeps latency low without raising voltage or fan speed.
Major-brand DRAM chips rated for 1600 MHz maintain the rated frequency during long sessions such as video editing or virtual machines. The dual-rank 2Rx8 organisation supports the full 16 GB capacity without throttling. Systems limited to 16 GB maximum memory will not benefit from additional modules.
Measured against everything we stock in Model-Specific Memory Upgrades, at today’s prices. Recalculated every night.
New to this? Buying memory and SSDs with crypto — what to check, what it costs to pay, and what is never asked for.
| Product | |
|---|---|
| Brand name | Computer Memory Solutions |
| Model name | CM10246412800SODRL |
| Total capacity | 16 GB (2 × 8 GB) |
| Product type | 204-Pin DDR3 SO-DIMM |
| Performance | |
| Rated speed | DDR3L 1600 (PC3L 12800) |
| Processor | |
| Chipset | Major Brand Chipset |
| Memory | |
| CAS latency | CL11 |
| Memory timings | 11-11-11 |
| ECC support | No |
| Buffer type | Unbuffered |
| Memory rank | 2Rx8 |
| Heat spreader | No |
| Power | |
| Rated voltage | 1.35 V |
| Compatibility | |
| Compatible systems | Hp Envy Touchsmart M7-J120Dx, M7-J178Ca, M7-1015Dx |
| In the box | |
| Included items | 2 Memory RAM Sticks |
Power off the notebook, remove the battery if accessible, open the memory compartment, align each 204-pin module with the slot key and press firmly until both side clips snap into place; the step often missed is pressing evenly on both ends so the module seats fully.
The unbuffered non-ECC modules have no moving parts and require no scheduled maintenance; replacement is only needed if a stick fails or the notebook is upgraded beyond the 16 GB maximum supported by the Envy TouchSmart models.
The DDR3L 1.35 V specification and CL11 timing set the electrical and latency ceiling; sustained workloads will hit the 1600 MHz bandwidth ceiling before any thermal throttle because the modules have no heat spreader.
More in Model-Specific Memory Upgrades
What you pay in, and what you read prices in.
Sent from your wallet at checkout
Display only — the catalogue is priced in USD
No currency matches that.
New here?
Already have one?
There is no automatic reset: this shop sends no mail, so there is no one-time link to ask for. Leave the address on the account and it gets picked up by hand.
Request noted
Nothing is on its way to your inbox — this shop sends no mail at all. Someone picks these up by hand.
Remembered it?