Enfain OM3 LC-ST Duplex Multimode Fibre Optic Cable 30m
A 30-metre OM3 duplex cable with LC and ST connectors carries 10-gigabit data at 850 nm through a 3.0 mm PVC jacket
- Low loss with 0.2 dB typical insertion
- High signal integrity from >38 dB return loss
- 10 Gbps multimode performance over 30 m
- Durable 3.0 mm PVC jacket for handling
- Wide operating range from -20 °C to +60 °C
Enfain OM3 Duplex Patch Cable
This 30 metre multimode fibre patch cable uses OM3 10-gigabit core glass terminated with LC and ST ceramic ferrules. It is built for installers connecting switches, servers or patch panels in data-centre or enterprise racks where 850 nm transmission is required. The aqua jacket identifies the OM3 rating at a glance.
Capacity and headroom for 10G links
The cable supports 1, 10 and 40 gigabit Ethernet over multimode distances with typical insertion loss of .2 dB and maximum of .3 dB. Return loss exceeds 38 dB, preserving signal integrity on short-reach uplinks. It is not suited for single-mode runs or wavelengths beyond 850 nm where a different core would be needed.
Build integration with 3.0 mm jacket
The 3.0 mm PVC jacket meets a 330 mm minimum bend radius and survives 1000 mating cycles across an operating range of -20 °C to +60 °C. Duplex LC-ST ends plug directly into mixed transceivers without adapters, freeing rack space otherwise used by hybrid couplers. Installers needing armoured or plenum-rated sheathing should select a different cable type.
How it compares
Measured against everything we stock in Fiber Optic Patch Cables, at today’s prices. Recalculated every night.
- Price $62.99
- Pricier than about 71% of the 812 comparable items (median $29.99).
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Specifications
No published specifications for this item yet.
Other versions of this model
5 more in the same range
Questions about this item
Will the 3.0 mm jacket fit alongside my older patch cords in the same tray?
The cable uses a 3.0 mm PVC jacket, which is a common diameter for multimode patch cords and will sit in standard cable management trays with similar-sized leads.
How can I verify the link is performing to the stated 0.2 dB typical insertion loss after installation?
Use a light source and power meter at 850 nm to measure end-to-end loss; a reading at or below 0.3 dB maximum confirms the connectors and fibre are within spec.
Does the 30 m length include both LC and ST connectors already terminated, or do I need to buy connectors separately?
The patch cord arrives as a finished duplex assembly with LC connectors on one end and ST connectors on the other, so no additional terminations are required.
More in Fiber Optic Patch Cables
Similar items
Tripp Lite N820-10M 32.81 ft 10Gb Aqua Duplex Multimode 50/125 Fibre Optic Cable
- Fiber Optic
- Aqua
Black Box Corporation EFN310-002M-LCLC Single-Mode 9-Micron Duplex Fibre Optic Cable LC-LC PVC 2-m 6.5-ft
- Others
- Yellow
FLUKE networks SC/SC Singlemode Fibre Optic Cable 6.56 ft
- 1 x SC Male Network
- Network Cable
Ergotron 97-563-062 Cable Management Kit Black 0.5 ft
- Cable Management Kit
- Black
PPA International HDMI 2.0 Fiber Optic Cable 100 ft CL3 Rated
- HDMI to HDMI
- Male to Male










