Innocard PCIe x4 Gen 4 ReDriver M.2 NVMe EDSFF 1C gender changer
Converts a PCIe x4 Gen 4 slot to M.2 NVMe or EDSFF 1C with a built-in ReDriver for 16 GT/s signal integrity
- Adapter typePCIe Gen4
- Converts M.2 NVMe or EDSFF 1C to PCIe 4.0 x4
- Built-in ReDriver boosts Gen 4 signals to 16 GT/s with 17 dB CTLE gain
- On-board 100 MHz clock buffer drives longer traces and cables
- SMBus switch, expander and I/O at addresses 0x6C, 0x71 and 0x21 enable BMC control
- PERST, WAKE and CLKREQ buffers support out-of-band management over extended links
Innocard PCIe Gen 4 ReDriver adapter
This Innocard adapter converts a PCIe 4.0 x4 slot to either an M.2 M-key NVMe SSD or an EDSFF 1C SSD. It is built for system integrators who need to install one drive type at a time in a standard add-in card form factor. The onboard ReDriver extends 16 GT/s differential signals across longer traces or cables.
Onboard ReDriver and clock buffer
A PCIe ReDriver with 17 dB CTLE gain compensates signal loss over extended routing. A 100 MHz clock buffer drives longer trace lengths and cables. SMBus interfaces at addresses 0x6C, 0x71 and 0x21 enable BMC and IPMI control of power, reset and presence detection for both drive formats.
PCIe 4.0 x4 electrical limit
The adapter operates within the PCI Express Base Specification Rev 4.0 and the CEM R4.0 08072019 document. Bandwidth is limited to the four lanes provided by the host slot. Signal integrity depends on the quality of the host routing and any cabling used beyond the card edge.
How it compares
Measured against everything we stock in Other Adapters & Couplers, at today’s prices. Recalculated every night.
- Price $77.99
- Pricier than about 90% of the 1,761 comparable items (median $18.99).
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Specifications
| Product | |
|---|---|
| Adapter type | PCIe Gen4 |
Questions about this item
Will the on-board PCIe ReDriver need any firmware updates or periodic recalibration during its service life?
The ReDriver is a fixed-gain analog circuit with its CTLE set to a maximum 17 dB boost; it has no programmable firmware and requires no recalibration.
What is the first signal-integrity limit reached when the adapter runs at PCIe 4.0 x4 16 GT/s continuously?
The CTLE maximum gain of 17 dB defines the equalisation ceiling; beyond that the 16 GT/s differential pairs cannot be recovered.
How much extra heat does the clock buffer and SMBus logic add when the card operates all day in a server chassis?
The on-board 100 MHz clock buffer, SMBus switch, I/O expander and PERST/WAKE/CLKREQ gates are low-power CMOS blocks that add negligible heat inside the chassis airflow.
More in Other Adapters & Couplers
Similar items
Innocard
Innocard MCIO 74P PCIe 5.0 to U.2 SFF-8639 Dual Port 50cm Cable
- PCIe Gen5
$76.99
0.00093956BTC
In stock
Cables To Go
Cables To Go 03411 Two Port Keystone Single Gang Wall Plate White
- White
- With a wide selecti…
$7.99$11.49−30%
0.00009751BTC
In stock
Innocard
Innocard SFF-TA-1016 PCIe 5.0 to U.3 SFF-8639 50cm gender changer
- PCIe Gen5
$76.99
0.00093956BTC
In stock
Monoprice Inc.
Monoprice Inc. 8729 S/PDIF Toslink gender changer White
- White
$7.99
0.00009751BTC
In stock