We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black PCIe 6-pin to dual 8-pin splitter cable with 60cm main lead and 20cm Y-branch, 18AWG copper conductors

Vszerda

Vszerda PCIe 6-pin to dual 8-pin splitter cable 60cm+20cm 18AWG

SKU CH-G994-9DP24

Splits one 6-pin PCIe connector into two 8-pin connectors using 18AWG copper wire with 60 cm and 20 cm lengths

  • Splits one 6-pin into two 8-pin connectors for multi-GPU power
  • 18AWG copper conductors deliver reliable current to each graphics card
  • Main 60 cm lead plus 20 cm Y-split gives flexible routing inside the case
  • Compatible with standard modular PSUs and listed mining breakout boards
  • Supports SLI and CrossfireX configurations for dual-card gaming setups

PCIe 6-pin to dual 8-pin splitter

This Vszerda cable splits one 6-pin PCIe output from a modular power supply into two 8-pin connectors. It uses 18AWG copper conductors and is intended for GPUs that require dual 8-pin power inputs. The main lead runs 60 centimetres and the Y-split tails add 20 centimetres each.

Upgrade when a PSU lacks enough 8-pin ports

The adapter replaces the need for a new power supply when your current unit only offers 6-pin PCIe outputs but the graphics card demands two 8-pin plugs. It is worth the jump for mining rigs using server PSUs such as the DPS-1200FB, DPS-1200QB, PS-2751-5Q, HSTSN-PL12, DPS-700LB, PS-2112-5L, DPS-750RB or DL580 models, and for any standard pin-map modular PSU including the Coolermaster Silent 1200W.

Simple plug-in but watch total draw

Installation is a direct male-to-male connection with no tools required. The main risk is exceeding the 6-pin source rating because two 8-pin loads now share one 6-pin feed. Builders who need guaranteed per-connector current limits or who run cards with three 8-pin sockets should not use this splitter.

How it compares

Measured against everything we stock in Internal PSU & Riser Cables, at today’s prices. Recalculated every night.

Price $11.99
Cheaper than about 65% of the 7,839 comparable items (median $14.99).

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Specifications

No published specifications for this item yet.

Questions about this item

Will the 60 cm main cable and 20 cm Y-split reach my graphics cards in a mid-tower case?

The main run is 60 cm from the PSU to the splitter, then each 8-pin branch adds 20 cm, giving plenty of length for typical mid-tower GPU placement.

Which way round do the 6-pin and 8-pin connectors go, and what is the common mistake?

Plug the single 6-pin male into the modular PSU port first, then attach the two 8-pin males to the GPU; the error is forcing an 8-pin into the PSU side.

The 18 AWG copper wires will carry how much current before I should consider replacing the cable?

18 AWG copper is rated for continuous loads well above typical dual 8-pin GPU draw; replace only if insulation cracks, pins discolour or you upgrade to a higher-wattage PSU.

More in Internal PSU & Riser Cables

Similar items