We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Red SATA cable with straight and right-angle 7-pin connectors, 18 inches long

Cables To Go

Cables To Go 10181 7-Pin 180° to 90° SATA cable Red 18

SKU CH-0G7C-QW7NR MPN 10181

Connects SATA drives with 180° and 90° angled plugs to reduce cable strain and improve airflow

  • Cable length0.5 ft (0.15 m)
  • Connector count2
  • Connector genderMale to Male
  • Product typeCable Connectors
  • Product colorRed
  • Overall length18 in (45.7 cm)
  • Angled connectors reduce cable strain for longer life
  • 180° to 90° design eases routing in tight cases
  • Red 18-inch cable cuts clutter and improves airflow
  • Male-to-male 7-pin SATA supports up to 6 Gbps transfers
  • RoHS compliant build meets environmental standards

Straight-to-angled SATA cable for tidy builds

This Cables To Go 10181 cable links a 7-pin SATA device to a motherboard or host controller using a 180° straight plug on one end and a 90° angled plug on the other. The 18-inch red cable is designed to reduce bend stress at the connector, helping the link last longer inside a chassis. It supports transfer rates up to 6 Gbps and meets RoHS requirements.

Builders routing drives in tight corners.

The right-angle connector lets the cable sit flat against a drive or motherboard header, improving airflow and cutting clutter in compact cases or crowded drive cages. The half-foot length suits adjacent ports but will not reach devices mounted far from the controller. Installers needing a straight-to-straight layout or a longer reach should choose a different cable.

One drive per cable at full 6 Gbps headroom

Each assembly carries a single device connection, so a SSD or hard drive gets the full 6 Gbps bandwidth with no sharing. The short 18-inch run keeps signal loss low, but the fixed length leaves no slack for rerouting if the drive bay moves. Multi-drive arrays will need one cable per device.

How it compares

Measured against everything we stock in SATA & eSATA Drive Cables, at today’s prices. Recalculated every night.

Price $6.99
Cheaper than about 85% of the 1,954 comparable items (median $13.99).

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Specifications

Product
Brand nameC2G
Model name10181
Product typeCable Connectors
Product colorRed
Ports & slots
Connector count2
Connector genderMale to Male
Size & build
Overall length18 in (45.7 cm)
Cable length0.5 ft (0.15 m)
Shipping weight0.02 kg
Package size102 × 57 × 13 mm

Questions about this item

Does my motherboard or host controller need a standard 7-pin SATA port to use the C2G 10181 cable?

Yes, both connectors on this cable are 7-pin Serial ATA male plugs, so your board or controller must provide matching 7-pin SATA ports.

Will the 180° and 90° angled ends fit alongside older straight SATA cables already routed in my case?

The mixed-angle design lets one end run flat against the motherboard while the other angles away, reducing interference with existing straight cables in tight spaces.

How can I verify the cable is delivering the supported 6 Gbps transfer rate after installation?

Check the negotiated link speed in your BIOS or operating-system disk utility; it should report 6 Gbps when the drive and controller both support that rate.

More in SATA & eSATA Drive Cables

Similar items