We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Two green circuit boards with black chips, no heat spreader, SODIMM form factor

NEMIX RAM

NEMIX RAM 16GB (2x8GB) DDR5 5600 CL46 SODIMM memory upgrade for Supermicro X14SAV-F

SKU CH-CMJN-C2G19

16 GB dual-channel DDR5 SODIMM kit running at 5600 MT/s with CL46 latency for the Supermicro X14SAV-F

  • Total capacity16 GB (2 × 8 GB)
  • Rated speedDDR5 5600 (PC5 44800)
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • CAS latencyCL46
  • Rated voltage1.1 V
  • Buffer typeUnbuffered

Size 16GB 2X8GB

  • Exact-match DDR5-5600 kit runs at rated speed
  • Verified fit for Supermicro X14SAV-F motherboard
  • Major OEM chips tested for stability at CL46
  • 262-pin SODIMM form factor matches system requirements
  • 16 GB dual-channel capacity with 1.1 V operation

16GB DDR5 SODIMM kit for Supermicro X14SAV-F

This 16GB kit contains two 8GB DDR5 5600 modules built to the exact 262-pin SODIMM form factor required by the Supermicro X14SAV-F motherboard. The 1Rx8 Non-ECC Unbuffered design matches the board's memory controller expectations for full-capacity recognition and rated-speed operation. Major OEM chips from Samsung Micron or Hynix provide tested stability at the specified timing and voltage.

Thermals noise and power at 1.1V

Operating at 1.10V the modules draw minimal power and generate low heat without a heat spreader. The Unbuffered Non-ECC design keeps electrical load light on the memory controller. Silent passive cooling suits compact laptop and small-form-factor chassis where fan noise must stay low.

CL46 timing at DDR5 5600 decides fit

The CL46 CAS latency at DDR5 5600 (PC5-44800) is the single specification that determines whether this kit runs at its rated speed on the X14SAV-F. If your system manual requires a different latency or voltage the modules may downclock or fail to post. Builders needing ECC registered DIMMs or a different pin count cannot use this kit.

How it compares

Measured against everything we stock in Model-Specific Memory Upgrades, at today’s prices. Recalculated every night.

Price $161.99
Cheaper than about 60% of the 21,161 comparable items (median $397.99).
Total capacity 16 GB (2 × 8 GB)
Lower than about 70% of the 20,941 comparable items (median 32 GB).
Price per GB $10.12 per GB
Typical for this category: the median of 20,941 items is $8.19 per GB.

New to this? Buying memory and SSDs with crypto — what to check, what it costs to pay, and what is never asked for.

Specifications

Product
Brand nameNEMIX RAM
Product lineNEMIX RAM Original Series Memory
Model nameDDR5 Non-ECC Unbuffered SODIMM Memory
Part numberMS44800-818K2
Total capacity16 GB (2 × 8 GB)
Product type262-Pin DDR5 SODIMM
Performance
Rated speedDDR5 5600 (PC5 44800)
Processor
ChipsetMajor OEM Samsung, Micron, Hynix
Memory
CAS latencyCL46
ECC supportNo
Buffer typeUnbuffered
Memory rank1Rx8
Heat spreaderNo
Power
Rated voltage1.1 V
Compatibility
Compatible systemsSupermicro
In the box
Included items16 GB 2 × 8 GB DDR5 5600 MHz PC5-44800 1Rx8 1.1 V 262-PIN Non-ECC SODIMM KIT

Other versions of this model

5 more in the same range

Questions about this item

How do I install the 262-pin DDR5 SODIMM modules in the Supermicro X14SAV-F, and which slot order should I follow?

Power off the system, open the chassis, align each module's notch with the slot key, insert at a slight angle until the gold contacts are hidden, then press down until the side clips click. Check the board manual for the approved population order before seating both 8 GB sticks.

What maintenance or replacement will the 1Rx8 non-ECC SODIMM kit need over time?

No scheduled maintenance is required. Keep the motherboard firmware current so the memory controller continues to initialise the 5600 MT/s CL46 timings at 1.10 V. If a module ever fails, the lifetime replacement warranty covers a swap.

What limit appears first when the 16 GB DDR5-5600 kit runs sustained workloads?

The memory controller's thermal throttle point is reached before the modules themselves, since the sticks have no heat spreader and operate at the standard 1.10 V JEDEC voltage. Adequate chassis airflow prevents early throttling.

More in Model-Specific Memory Upgrades

Similar items