We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black sleeved Molex to four PWM fan splitter cable, 16 inches

EN-Labs

EN-Labs IDE24PWM16 Molex to 4×PWM fan splitter 16" black

SKU CH-31RR-PDP07

Connects four PWM or three-pin fans to one Molex PSU header while returning RPM feedback to the motherboard over a 16-inch 26AWG sleeved cable

  • Connector count6
  • Connector genderMale to Male
  • Product typeCable Splitters
  • Product colorBlack
  • Overall length16 in - 20 in
  • DetailsType :PWM fan power cable Length: 16 in Conductor:26AWG Copp
  • Powers four PWM fans from one Molex connector
  • 16-inch sleeved cable reaches chassis fans cleanly
  • 26AWG copper conductors deliver stable 12 V power
  • RPM feedback wire sends speed data to motherboard header
  • Fans run synchronised under PWM control for balanced cooling

Purpose and audience

The EN-Labs IDE24PWM16 is a Molex to four-way PWM fan splitter that lets a single power-supply header drive up to four case or CPU cooler fans. It is built for system builders who want to add extra airflow without overloading a motherboard fan header.

Practical limits of the interface

The adapter draws 12 V power directly from the PSU through a 26 AWG copper cable, so the motherboard header only carries the PWM control and RPM feedback signal. When a 3-pin fan is connected, speed regulation is not available because the third pin carries only a tachometer signal. Cable length is 16 inches with a sleeved black finish.

Installation and common issues

One male Molex LP4 plug goes to the PSU, four male 4-pin fan plugs go to the fans, and a single female 4-pin plug connects to the motherboard CPU or SYS fan header for RPM reporting. All attached fans spin at the same PWM duty cycle, so individual speed curves are not possible. Buyers who need per-fan speed control or more than four fans on one header should look for a powered fan controller instead.

How it compares

Measured against everything we stock in Internal PSU & Riser Cables, at today’s prices. Recalculated every night.

Price $5.99
Cheaper than about 94% of the 7,839 comparable items (median $14.99).

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Specifications

Product
Brand nameEn-Labs
Model nameIDE24PWM16
Product typeCable Splitters
Product colorBlack
Ports & slots
Connector count6
Connector genderMale to Male
Size & build
Overall length16 in - 20 in

Questions about this item

How do I choose between the 16-inch and 20-inch lengths for this PWM fan splitter?

The cable measures 16 inches from the Molex plug to the first fan connector; the 20-inch figure is the maximum reach to the furthest branch, so pick 16 inches for tight routing or 20 inches if you need extra slack across a large chassis.

What does the 12 V rating mean once the splitter is installed in my PC?

It confirms the adapter delivers standard 12 V power from the PSU Molex rail to every connected fan, allowing up to four 12 V PWM or 3-pin fans to run without drawing current from the motherboard header.

How does the Molex LP4 interface limit the number of fans I can connect?

The single Molex 4-pin plug supplies all four fan branches, so the practical limit is the PSU rail’s current capacity; the cable itself provides four 4-pin PWM outputs plus one 4-pin female header for RPM feedback to the motherboard.

More in Internal PSU & Riser Cables

Similar items