Vszerda SATA Power Y Splitter Cable 15 Pin Male to Dual Female 7 Inch 2 Pack
Turns one SATA power port into two 15-pin connectors for extra drives or optical units
Pack 2 packs
- 1 Pack$5.99
- 2 packs$6.99
- Turns one SATA power port into two for extra drives
- 7 inch 18 AWG cable keeps builds tidy
- 15 pin male to dual 15 pin female connectors
- Powers 2.5 and 3.5 inch drives plus optical units
- Supplies 3.3V 5V and 12V from single PSU connection
Practical Power Expansion
This SATA power Y splitter cable turns a single 15 pin connector from the power supply into two female ports. The 7 inch length suits tight chassis routing while supporting 2.5 inch SSDs, 3.5 inch hard drives and optical drives. Builders and upgraders gain extra device connections without replacing the PSU.
Wiring and Daily Use
Each splitter uses 18 AWG conductors rated for 3.3V, 5V and 12V rails from a standard ATX supply. The straight male plug and two female receptacles fit directly into existing cables, so no tools or adapters are required. Cable stiffness is moderate, allowing neat bundling behind the motherboard tray.
Current Limits and Planning
Total draw across both branches must stay within the source connector and PSU rail ratings. The 18 AWG gauge sets a practical ceiling lower than a dedicated PSU lead, so high spin up loads on multiple mechanical drives need checking. Verify the power supply label before adding several devices on one splitter.
How it compares
Measured against everything we stock in SATA & eSATA Drive Cables, at today’s prices. Recalculated every night.
- Price $6.99
- Cheaper than about 85% of the 1,954 comparable items (median $13.99).
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Specifications
No published specifications for this item yet.
Other versions of this model
1 more in the same range
Questions about this item
Does the 15-pin SATA power splitter pass 3.3 V, 5 V and 12 V to both drives?
Yes, the cable carries 3.3 V, 5 V and 12 V from the PSU to each 15-pin female connector.
What clearance is needed for the 7-inch Y-cable inside a case?
The 7-inch (20 cm) length and 18 AWG wire allow routing behind motherboard trays or along drive cages in standard towers.
How do I connect the splitter without overloading the PSU rail?
Plug the single male end into the PSU SATA port, attach two drives to the female ends, then verify the PSU’s total 12 V current rating covers the added load.
More in SATA & eSATA Drive Cables
Similar items
STARTECH SATA36RA1 36in Right-Angle SATA Cable
- Cable Connectors
- Red
Nippon Labs SATA3L1.5FT-90/180RD 1.5 ft SATA III cable 90 to 180 degree
- 1.5 ft (0.46 m)
- SATA III
Nippon Labs SATA-0.5RR 0.5m SATA cable right-angle pair
- 1.64 ft (0.5m)
- SATA II
EN-Labs SATA18BK90 SATA cable 18 inch 90 to 180 degree latching
- 18 in (45.7 cm)
- Cable Connectors
STARTECH SATAPOWADPL 6 in 4 pin Molex to left angle SATA power adapter cable
- 6 in (15.2 cm)
- Cable Connectors
EN-Labs SATA18UVGN-3PACK 3-pack 18 inch SATA cable
- 1.5 ft (0.46 m)
- Cable Kits






