We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black shielded Cat6A patch cable one foot long with gold RJ45 plugs

SANOXY

SANOXY Cat6A Ethernet Cable 1FT Shielded STP 10Gbps 500MHz 26AWG Pure Copper Gold Plated RJ45 Non-Booted Black

SKU CH-N1TD-QF8H4

A 1-foot shielded Cat6A patch cord with pure copper conductors, gold-plated RJ45 contacts, and a space-saving non-booted design for 10Gbps links in dense racks

Length 1 ft.

Show 3 more
  • 10Gbps speed and 500MHz bandwidth for low-latency streaming and gaming
  • Shielded STP construction reduces electromagnetic interference and crosstalk in busy environments
  • Pure bare copper 26AWG conductors ensure excellent conductivity and minimal signal loss
  • 50-micron gold-plated RJ45 contacts resist corrosion for long-term stable performance
  • Non-booted connector saves space and simplifies installation in high-density patch panels

Ultra-Short 1FT Patch Cable

This 1FT Cat6A Ethernet patch cable is built for close-range links between patch panels, switches and side-by-side devices in high-density racks. Its shielded STP construction reduces electromagnetic interference and crosstalk, keeping signals clean in crowded cabinets. Stranded 26AWG pure bare copper conductors and 50-micron gold-plated RJ45 contacts deliver reliable conductivity and corrosion resistance. The non-booted connector profile saves valuable port space in tight installations.

Upgrade From Unshielded Or Longer Runs

The jump is worth it when you replace an unshielded Cat5e or Cat6 patch cord that suffers interference in dense equipment rooms, or when a longer cable creates slack that blocks airflow. Shielding and 500MHz bandwidth support 10Gbps speeds over this short distance, eliminating the noise and latency that degrade streaming, gaming or cloud workloads. If your existing runs are already shielded, correctly terminated and fit the space, the improvement will be marginal.

Tool-Less Press-Fit Installation

Push the non-booted RJ45 plugs straight into the ports until they click — no latch tab to depress and no boot to clear in crowded panels. The only common issue is inserting the connector upside down, which feels tight but will not seat; flip it and press again. Because the cable is only 1FT long, verify the port spacing before ordering so the reach matches your exact panel layout.

How it compares

Measured against everything we stock in Ethernet & LAN Cables, at today’s prices. Recalculated every night.

Price $8.99
Cheaper than about 77% of the 9,945 comparable items (median $14.99).

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Specifications

No published specifications for this item yet.

Other versions of this model

5 more in the same range

Questions about this item

What connectors and spacing does the 1FT non-booted RJ45 cable need to fit?

The non-booted RJ45 plugs fit standard keystone jacks and high-density switch ports without the extra clearance that booted connectors require.

How do I install the shielded STP cable correctly, and what step is often missed?

Terminate each end using Cat6A-rated shielded RJ45 plugs, connect the drain wire to a grounded patch panel or jack, and avoid kinking the 26AWG stranded conductors during routing.

What maintenance or replacement will the gold-plated contacts and shielding need later?

The 50-micron gold plating resists corrosion, so contacts rarely need cleaning; replace the cable only if the shield is cut, the jacket is damaged, or a connector tab breaks.

More in Ethernet & LAN Cables

Similar items